550959 e temposonics linear sensors use the time-based magnetostrictive posi- tion sensing principle developed by mts. within the sensing element, a sonic strain pulse is induced in a specially-designed magnetostrictive waveguide by the momentary inter- action of two magnetic fields. one field comes from a movable perma- nent magnet that passes along the outside of the sensor. the other field comes from an ?nterrogation current pulse applied along the waveguide. the resulting strain pulse travels at ultrasonic speed along the waveguide and is detected at the head of the sensing element. the position of the magnet is deter- mined with high precision and speed by accurately measuring the elapsed time between the application of the interrogation pulse and the arrival of the resulting strain pulse with a high speed counter. using the elapsed time to determine position of the permanent magnet provides an absolute position reading that never needs recalibration or re-homing after a power loss. non-contact sensing eliminates wear, and guar- antees the best durability and output repeatability. temposonics next generation platform optimized for performance, durability and functionality advanced sensor communication via serial rs-422, rs-485 or infrared interfaces enhanced diagnostics and programming capability using serial communications and visual leds designed for backwards compatibility with legacy t emposonics products all specifications are subject to change. please contact mts for specifications that are critical to your needs. refer to ?ow to order? on page 7 or go to www.temposonics.com for the latest list of g-series support documentation. temposonics magnetostrictive position sensors g-series linear position sensor analog and digital pulse outputs product specification the benefits of magnetostrictive sensing temposonics model gp temposonics model gh
measured variable: displacement resolution: analog: infinite digital: 1 [gradient x crystal freq. (mhz) x circulation] non-linearity: 0.02% or 0.05 mm ( 0.002 in.), whichever is greater repeatability: 0.001% of full stroke or 0.0001 in. ( 0.0025 mm), whichever is greater. outputs: analog: voltage or current digital: start/stop or pwm measuring range: hydraulic-rod style: analog: 50 to 2540 mm (2 to 100 in.)* digital: 50 to 7620 mm (2 to 300 in.) profile style: analog: 50 to 2540 mm (2 to 100 in.)* digital: 50 to 5080 mm (2 to 200 in.) operating voltage: +24 vdc nominal (20.4 - 28.8 vdc) standard +9 to +28.8 vdc optional operating temperature: - 40 to +80 ?, (85 ? max.**) - 40 to +176 ? (185 ? max.**) emc test: emissions iec/en 61000-6-3, immunity iec/en 61000-6-2, iec/en 61000-4-2/3/4/5/6/8, level 3/4 criterium a, ce qualified shock rating: 100 g (single hit)/iec standard 68-2-27 (survivability) vibration rating: 5 g/10-2000 hz/iec standard 68-2-6 adjustability: field adjustable null and span (for analog sensors only) update time: analog: < 1 ms (typical) digital (external interrogate): minimum = (2.5 + null + stroke) x 10.0 ?/in. x (number of recirculations) profile style (gp model) electronic head: aluminum housing sealing: ip 65 sensor extrusion: aluminum (temposonics profile style) mounting: adjustable mounting feet or t-slot m5 nut in base channel magnet type: captive-sliding magnet or floating magnet rod style (gh model) electronic head: aluminum housing sealing: ip 67 sensor rod: 304l stainless steel operating pressure: 350 bar static, 690 bar spike (5000 psi static; 10,000 psi spike) mounting: threaded flange m18 x 1.5 or 3/4-16 unf-3a typical mounting torque: 45 n-m (33 ft. - lbs.) magnet type: ring or floating magnet * stroke lengths longer than 2540 mm (100 in.) for analog output are available on a custom basis. ** consult factory for high temperature applications. the above specifications for analog output sensors are based on the assumption that output ripple is averaged by the measuring device as with any typical analog device. to controller, meter or other device 0 to 10 vdc 10 to 0 vdc -10 to +10 vdc +10 to -10 vdc 4 to 20 ma 20 to 4 ma 0 to 20 ma 20 to 0 ma active stroke length (measuring range) sensor ouput null (setpoint 1) span (setpoint 2) temposonics g-series position sensors with analog outputs provide direct signal s, including voltage (0 to 10 vdc or -10 to +10 vdc, forward or reverse acting) and current (4 to 20 ma, or 0 to 20 ma, forward or reverse acting). both voltage and current outputs allow full adjustments of null and span set- points, (minimum 2 in. between setpoints). since the outputs are direct, no signal-conditioning electronics are needed when interfacing with controllers or meters. pulse width is proportional to magnet position start pulse pwm start/stop + start - start + gate - gate to controller, meter, or other device input signals to sensor magnet time between start and stop pulses is proportional to magnet position start pulse reflection stop pulse + stop - stop output signals from sensor temposonics g-series position sensors provide direct start/stop and pwm signals. standard resolution is 0.004 in. with digital pulse outputs (when using a 28 mhz counter). higher resolutions are possible with increased circulations or with the use of higher resolution counters. mts sensors, the inventors of magnetostrictive position sensing and makers of temposonics sensors, is proud to introduce our new g-series linear posi- tion sensors utilizing our next generation technology platform. g-series position sensors feature a microprocessor-based design with enhanced diag- nostics and programmability to maximize backwards compatibility. backwards compatibility is one of the primary benefits of the new g-series position sensor. g-series position sensors provide the same functionality as tempo ii and l-series sensors making them an ideal direct replacement for these products. in addition to providing advanced programming and diagnostic capabilities in a rugged package, g-series position sensors also include the following fea- tures: electronics housing small enough to allow for drop in replacements of legacy temposonics products. standard 24 vdc and extended input power supply options for compatibility with older controller interfaces. fully adjustable voltage and current outputs within: -10 to +10 vdc or +10 to -10 vdc 0 to 20 ma or 20 to 0 ma all outputs are available up to 300 in. stroke length (hydraulic-rod style) up to 15 magnet positions simultaneously using the start/stop output option. integral connector replacement options including: hanging (inline) connectors adapter cables field-installed connector kits 2 analog outputs digital-pulse outputs parameter specification the next generation temposonics mts sensors product specification 550959 e
temposonics g-series sensors are preconfigured at the factory by model code designation. for many applications no adjustments are required for normal sensor installation and operation. if, however, sensor parameter changes are desired while in the field, the g-series sensor is easily pro- grammed. using external communication for monitoring and programming, there is no need to open the sensor s electronics housing. this can simplify installation and commissioning, saving valuable time. keeping the sensor electronics isolated ensures that seal integrity and the highest product reliability are maintained. the new platform technology inside the g-series position sensor enables: infrared (ir) send and receive for wireless communication. built-in serial interfaces for robust hard-wired serial communication, (rs-422 for digital-pulse outputs and rs-485 for analog outputs). remote programmability for operational modes and sensor parameters. enhanced monitoring and diagnostic capabilities (see below). programmable modes and sensor parameters for g-series position sensors include: for digital-pulse outputs start/stop or pwm output mode internal or external interrogation mode for pwm mode number of recirculations (1 to 15) for pwm mode for analog outputs voltage or current output mode voltage or current output range full adjustment for null and span setpoints the g-series simple visual user interface helps resolve the majority of cus- tomer installation and troubleshooting issues. integrated leds indicate (refer to led indicator table): normal operating conditions error conditions, power and sensor/control interface issues programming modes (ir or hard wired) hard-wired g-series serial communication enables diagnostic feedback at a convenient remote location. access to internal sensor conditions minimizes troubleshooting efforts and enables the development of more sophisticated controller diagnostic routines. all of these features will simplify sensor installation and maximize operational productivity. green red description off off no power to sensor off on self-diagnostic error off flashing ir programming mode on off normal sensor function on on magnet not detected on flashing missing (external) interrogation flashing off serial programming mode flashing on magnet signal weak flashing flashing power out of range (high or low) g-series pc configuration & diagnostics software user interface g-series electronics housing with built-in leds g-series led indicator table g-series output setup g-series sensor information 3 advanced communication and programmability enhanced monitoring and diagnostics g-series ir setpoint programmer (for analog output sensors) part number 380078 recall ir signal g-series analog handheld programmer part number 253294 mts sensors product specification 550959 e
led window 44 mm (1.7 in.) 68 mm (2.7 in.) 50.8 mm (2.00 in.) integral connector beginning of stroke (null position) end of stroke electronics housing null zone stroke length flat-faced hex flange a sensor rod o10mm (0.39 in.) 25 mm (0.98 in.) dead zone stroke dependent refer to chart below m4 x 59 mm button-head hex screws (2x) o-ring model gh rod-style sensor the temposonics g-series rod-style sensor (model gh) offers modular construction, flexible mounting configurations, and easy in stallation. it is designed for internal mounting in applications where high pressure conditions exist, (5000 psi continuous, 10,000 psi spike), such as hy draulic cylinders. the model gh sensor may also be mounted externally in many applications. o-ring non-ferrous spacer (part no.: 400633). see notes. chamfered-rod bushing (customer provided, optional) threads (3/4-16 unf-3a or m18 x 1.5 metric threads) null standard: 50.8 mm (2.0 in.) stroke length 12.7 mm (0.5 in.) bore sensor rod 10.0 mm (0.394 in.) dia. dead zone see notes position magnet integral cable piston head & rod assembly 43 mm (1.7 in.) when used for hydraulic cylinders, the sensor s high pressure, stain- less-steel rod installs into a 1/2 in. bore in the piston head/rod assem- bly as illustrated. the model gh sensor cartridge can be removed from the flange and rod housing while still installed in the cylinder. this procedure allows quick and easy sensor cartridge replacement, without the loss of hydraulic pressure. notes: the position magnet requires minimum distances away from ferrous metals to allow proper sensor output. the minimum distance fro m the front of the magnet to the cylinder end cap is 15 mm, (0.6 in.). the minimum distance from the back of the magnet to the piston head is prov ided by the non-ferrous spacer, i.e. 3.2 mm, (0.125 in.). the illustration above represents a typical installation. some installation requirements may be application specific. b 68 mm (2.7 in.) a raised-face hex flange grounding lug mating connector (6 pin din style) 76 mm (3.0 in.) 25 mm (0.98 in.) 2.5 mm (0.10 in.) 25.4 mm (1.00 in.) 50.8 mm (2.00 in.) beginning of stroke (null position) null zone o-ring c stroke-dependent dead zones stroke length dead zone 50 - 5000 mm (2 - 197 in.) 63.5 mm (2.5 in.) 5005 - 7620 mm (197.1 - 300 in.) 66 mm (2.6 in.) housing style flange type description a flange threads b dimensions c dimensions t us customary threads with raised-face hex 3/4?16 unf-3a 44.5 mm (1.75 in.) 51 mm (2.0 in.) s us customary threads with flat-faced hex 3/4?16 unf-3a 44.5 mm (1.75 in.) 51 mm (2.0 in.) m metric threads with flat-faced hex m18 x 1.5 46 mm (1.81 in.) 53 mm (2.1 in.) 4 cylinder installation mts sensors product specification 550959 e
model gp profile-style sensor temposonics model gp profile-style sensors offer modular construction, flexible mounting configurations, and easy installation. a choice of two magnet configurations are available with the profile housing: captive-sliding magnet or floating magnet. led window 45 mm (1.77in.) 64 mm (2.5 in.) 12 mm (0.47 in.) 82 mm (3.2 in.) integral connector beginning of stroke (null position) end of stroke electronics housing dead zone grounding lug 44 mm (1.73 in.) 14.5 mm (0.57 in.) stroke length mounting feet part no. 400802 aluminum extrusion profile-style null zone mounting foot part no. 400802 m5 screw (2x) or #10 screw (2x) 1.9 mm (0.075 in.) mating connector (6-pin din style) captive-sliding magnet style v part no. 252184 captive-sliding magnet style s part no. 252182 36 mm (1.42 in.) vertical: 18 o horizontal: 18 o vertical: 18 o horizontal 360 o 45 mm (1.77 in.) 76 mm (3.0 in.) 12 mm (0.47 in.) null zone 9.1 mm (0.36 in.) 35.5 mm (1.40 in.) 50 mm (1.97 in.) 68 mm (2.68 in.) 28 mm (1.10 in.) 45 mm (1.77 in.) 52 mm (2.05 in.) integral cable 28 mm (1.10 in.) null zone floating magnet style m part no. 251416 beginning of stroke (null position) 66 mm (2.6 in.) dead zone stroke length end of stroke non-ferrous mounting support and screws 43 mm (1.7 in.) 49 mm (1.93 in.) max gap 3mm 1mm (0.12in. 0.04in.) floating magnet style m 5 mm (0.20 in.) t-slot nut, m5 thread (optional, sold separately) m5 threaded stud and nut note: temposonics model gp sensors include two mounting feet (part no. 400802) for sensors up to 1250 mm (50 in.) one additional mounting foot is included for every additional 500 mm (20 in.) captive-sliding magnet 5 floating magnet (open ring) mts sensors product specification 550959 e
pin no. wire color function function digital-pulse outputs analog outputs 1 gray (-) gate for pwm 0 to 10, -10 to +10 vdc or (-) stop for start/stop or 4 to 20 ma, 0 to 20 ma programming (rs-422 tx-) or reverse acting: 10 to 0, 10 to -10 vdc or 20 to 4 ma, 20 to 0 ma 2 pink (+) gate for pwm return for pin 1 (+) stop for start/stop or programming for (rs-422 tx+) 3 yellow (+) interrogation for pwm programming (rs-485+) (+) start for start/stop or programming (rs-422 rx+) 4 green (-) interrogation for pwm programming (rs-485-) (-) start for start/stop or programming (rs-422 rx-) 5 red or brown supply voltage (+vdc) supply voltage (+vdc) 6 white dc ground (for supply) dc ground (for supply) pinout/wire color code (integral or extension cable) integral d6 connector (male) as viewed from end of sensor cable connectors (field-installed d6 female) mates with sensors integral connector wiring and magnets notes: ?a grounding lug on the end of the sensor is provided for convenient connection to earth ground. ?appropriate grounding of cable shield is required at the controller end. 18 mm (0.7 in.) 54 mm (2.1 in.) 54 mm (2.1 in.) 37 mm (1.5 in) magnets must be ordered separately with model gh position sensors. the standard ring magnet (part no. 201542-2) is suitable for most applications. magnets are included when you order the model gp position sensor. the sensor can be configured with one of two magnet configurations: captive-sliding or floating magnet (open ring). d6 straight-exit connector part no. 560700 d6 90?connector part no. 560778 18 rotation 24 mm (0.95 in.) 57 mm (2.24 in.) 14 mm (0.55 in.) 40 mm (1.58 in.) 9 mm (0.35 in.) ball-jointed arm, m5 thread rotation: vertical: 18 horizontal: 360 24 mm (0.95 in.) 43 mm (1.69 in.) 14 mm (0.55 in.) 40 mm (1.58 in.) 20 mm (0.79 in.) ball-jointed arm, m5 thread captive-sliding magnet, style v part no. 252184 captive-sliding magnet, style s part no. 252182 floating magnet (open ring), style m (may be used with models gh and gp sensors) part no. 251416-2 4 holes each 4.3 mm dia. (0.17 in.) 90?apart on 23.9 mm dia. (0.94 in.) id: 13.5 mm (0.53 in.) od: 32.8 mm (1.29 in.) thickness: 7.9 mm (0.312 in.) 120 24.6 mm (0.97 in.) 2 holes each 4.3 mm dia. (0.17 in.) on 23.9 mm dia. (0.94 in.) 14 mm (0.57 in.) 20.7 mm (0.81 in.) id: 13.5 mm (0.53 in.) od: 32.8 mm (1.29 in.) thickness: 7.9 mm (0.312 in.) magnet spacer (non-ferrous spacer for use with standard ring magnet) part no. 400633 standard-ring magnet part no. 201542-2 id: 13.5 mm (0.53 in.) o.d.: 25.4 mm (1.0 in.) thickness: 7.9 mm (0.312 in.) ring magnet part no. 400533 id: 14.3 mm (0.56 in.) o.d.: 31.8 mm (1.25 in.) thickness: 3.2 mm (0.125 in.) each 3.9 mm o.d. (0.15 in.) 90 o apart on 23.9 mm o.d. (0. 4 holes 1 2 3 4 5 6 specific gravity: 0.70 max. pressure: 870 psi max. (float for use with rod-style sensors in hydraulic fluid or fresh water applications only) 14 mm (0.55 in.) min. id 51 mm (2.0 in.) spherical od 3.4 mm (0.134 in.) c 53 mm (2.09 in.) l magnet float (level sensing applications) part no. 251447 6 sensor integral connector (d60 male) magnets mts sensors product specification 550959 e
how to order when placing an order, build the desired model number using the model number guide (right). a wide range of g-series position sensor configurations are available to meet the demands of your particular application. if you have any questions about how to apply g-series position sensors, please contact mts applications engineering or your local mts dis- tributor. both of these resources are available to assist you in designing an effective position sensing system to fit your application. notes: refer to g-series cross reference part numbers 550967 and 550956 for information about backwards compatible replacement options, including integral cables with in-line connectors, adapter cables, and field-installed connector kits. contact the factory for specials. refer to the g-series user s manual , part no. 550966 for initial setup information. refer to g-series installation drawings , part no s. 550953 and 550955 for installation information. sensors connection type d6 = female connector (straight-exit) for sensors with d6 (d60) connector da = female connector (90 exit) for sensors with d6 (d60) connector cable lengths for standar d length cables up to 100 ft. 005 = 5 ft. 050 = 50 ft. 015 = 15 ft. 100 = 100 ft. 025 = 25 ft. for custom length cables over 100 ft. __ __ __ = cable length (maximum cable length is dependent on the output selected; consult mts applications engineering.) cable termination po = pigtail connection d6m = 6-pin d6 male connector (straight exit) sensor model gh = hydraulic rod style gp = profile style housing style t emposonics model gh only (magnet must be ordered separately): t = us customary threads, raised-faced hex, and pressure tube s = us customary threads, flat-faced hex, and pressure tube m = metric threads, flat-faced hex, and pressure tube b = sensor cartridge only (no application housing, stroke lengths 1 to 72 in.) t emposonics model gp only (magnet included): m = floating magnet ( open ring, part no. 251416-2 ) s = captive-sliding magnet with joint at top ( part no. 252182 ) v = captive-sliding magnet with joint at front ( part no. 252184 ) stroke length __ __ __ . __ u = inches and tenths (encode in 0.2 in. increments) __ __ __ __ m = millimeters (encode in 5 mm increments) connection type integral connector d60 = 6-pin din, standard integral cables r __ __ = integral cable, pvc jacket, pigtail termination. cable length __ __ = encode in feet if using us customary stroke length, encode in meters if using metric stroke length range = 1 (01) to 99 (99) ft. or 1 (01) to 30 (30) meters input voltage 1 = + 24 vdc (+20%, - 15%), standard 2 = +9 to +28.8 vdc. output v oltage v0 = 0 to +10 vdc v2 = -10 to +10 vdc v1 = +10 to 0 vdc v3 = +10 to -10 vdc cur r ent a0 = 4 to 20 ma a2 = 0 to 20 ma a1 = 20 to 4 ma a3 = 20 to 0 ma digital pulse ro__ = start/stop. if more than one magnet, the _ denotes number of magnets in hexadecimal (refer to table c) d__ __ = pulse-width modulated (pwm) (fill in the two blanks with the following codes.) table a: circulation count vs. resolution for pwm output (based on 28 mhz counter) resolution circulation count* 0.00026 in. (0.0066mm) 15 0.0005 in. (0.0127 mm) 8 0.001 in. (0.025 mm) 4 0.002 in. (0.051 mm) 2 0.004 in. (0.102 mm) 1 2 or 3 digit code depending on output selected cable length notes: ? mts recommends the maximum integral cable length to be 10 meters or 33 feet. ?cables greater than 10 meters in length are available, however, proper care must be taken during handling and installation. a b a) inter r ogation b) cir culations e = external __ = desired number of circulations i = internal range = 1 to 15; encode in hexadecimal (refer to tables a, b and c). *limited by stroke length for sensors configured for internal interrogation. (refer to table b.) g 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 stroke length notes: gh voltage or current = 2-100 in. (50-2540 mm). ?gh digital pulse = 2-300 in. (50-7620 mm). ?gp voltage or current = 2-100 in. (50-2540 mm). ?gp digital pulse = 2-200 in. (50-5080 mm). table b: maximum circulation count vs stroke for pwm output w/internal interrogation resolution maximum circulation count < 84 in. (2134 mm) 15 > 84 in. (2134 mm) 1 extension cable with connectors for the d6, (d60), connection type (uses standard type cable) 7 position sensor d l-series retrofit note: ? for stroke lengths < or = to 60 in., either +15 volts or +24 volts could be used for l-series. choose the appropriate g-series option based on the power supply used. choose option 2 if not certain. ? for stroke lengths > 60 in., select g-series option 1. table c: decimal: 1 2 3 4 5 6 7 hexadecimal: 1 2 3 4 5 6 7 decimal: 8 9 10 11 12 13 14 15 hexadecimal: 8 9 a b c d e f mts sensors product specification 550959 e
description function/notes par t no. mounting feet, standard (spares) model gp sensors come with mounting feet (see page 5). 400802 base channel t-slot nut nut for mounting model gp sensors. requires m5 screw (see page 5). 401602 hex jam nut 3/4-16 unf nylon insert locknut for use with model gh sensors 500015 with style ??or ??housings hex jam nut m18 x 1.5 for use with model gh sensors with style ??housing 500018 o-ring (spare) for use with model gh sensors with style ??or ??housings 560315 o-ring (spare) for use with model gh sensors with style ??housing 401133 joint-rod sleeve (1 in.) for use with model gp sensors with ??or ??style magnets 401603 ball-jointed arm, straight for use with model gp sensors with ??or ??style magnets 401913 description function/notes par t no. small open ring (model gp spare) magnet style m, ?loating?magnet used with model gh and gp sensors. 251416-2 small ring magnet standard magnet for model gh sensors. 201542-2 magnet float for use with model gh sensors used to measure liquid level. 251447 captive-sliding magnet (spare) style s captive-sliding magnet with joint at top. comes with gp sensors. 252182 captive-sliding magnet (spare) style v captive-sliding magnet with joint at front. comes with gp sensors. 252184 magnet spacer for use with standard ring magnet, part no. 201542. 400633 collar provides end of stroke ?tops?for magnet float, part no. 251447. 560777 magnet mounting screws used to mount the standard ring magnet, part no. 201542. 560357 (4 screws required) description function/notes par t no. 6-pin din connector, straight female, straight exit, mates to d60 connection type. see page 6. 560700 6-pin din connector, 90 female, 90 exit, mates to d60 connection type. see page 6. 560778 description function/notes par t no. g-series documentation and includes g-series pc setup software part no. 625060*, g-series palm os 550971 software cd software part no. 625061*, g-series quick start part no. 550966 and additional documentation. infrared setpoint programmer for adjusting null (setpoint 1) and span (setpoint 2) on g-series 380078 analog sensors. rs-485 & rs-422 provides hardware interface for g-series to rs-232 converter pc setup software. 380077 * download at no charge from website (www.mtssensors.com). united states mts systems corporation sensors division 3001 sheldon drive cary, nc 27513 tel: 800-633-7609 fax: 919-677-0200 800-498-4442 www.mtssensors.com sensorsinfo@mts.com germany mts sensor technologie gmbh & co. kg auf dem sch?ffel 9 d - 58513 l?denscheid tel: +49 / 23 51 / 95 87-0 fax: +49 / 23 51 / 56 491 www.mtssensor.de info@mtssensor.de japan mts sensors technology corporation ushikubo bldg. 737 aihara-cho, machida-shi tokyo 194-0211, japan tel: + 81 (42) 775 / 3838 fax:+ 81 (42) 775 / 5512 www.mtssensor.co.jp info@mtssensor.co.jp part number: 09-06 550959 revision e mts and temposonics iare registered trademarks of mts systems corporation. all other trademarks are the property of their respective owners. all temposonics sensors are covered by us patent number 5,545,984. additional patents are pending. printed in usa. copyright ?2006 mts systems corporation. all rights reserved. 50 mm (1.97 in.) 68 mm (2.68 in) 9.1 mm (0.36 in.) 9.1 mm (0.36 in.) 0.213 in. dia. through 4 holes 304 sst 27.9 mm (1.1 in.) 1.9 mm (0.075 in.) width = 14.5 mm (0.57 in.) mounting foot standard mounting foot part no. 400802 14 mm (0.55 in.) m5 threads rotation: 18 allowable 9 mm (0.35 in.) m5 inside thread (2) (1) 22 mm (0.87 in.) 27 mm (1.06 in.) extension rod lengths part no. 60.3 mm (2.375 in.) 401768-2 85.7 mm (3.375 in.) 401768-3 111.1 mm (4.375 in.) 401768-4 161.9 mm (6.375 in.) 401768-6 187.3 mm (7.375 in.) 401768-7 212.7 mm (8.375 in.) 401768-8 238.1 mm (9.375 in.) 401768-9 263.5 mm (10.375 in.) 401768-10 314.3 mm (12.375 in.) 401768-12 365.1 mm (14.375 in.) 401768-14 extension rod lengths part no. 390.5 mm (15.375 in.) 401768-15 466.7 mm (18.375 in.) 401768-18 517.5 mm (20.375 in.) 401768-20 542.9 mm (21.375 in.) 401768-21 619.1 mm (24.375 in.) 401768-24 771.5 mm (30.375 in.) 401768-30 923.9 mm (36.375 in.) 401768-36 1076.3 mm (42.375 in.) 401768-42 1228.7 mm (48.375 in.) 401768-48 1533.5 mm (60.375 in.) 401768-60 9.5 mm (0.375 in.) m5-0.8 thread bor e (both ends) 15.2 mm (0.60 in.) (both ends) extension rod part no. 401768-xx joint rod used with captive-sliding magnets (1) sleeve, part no. 401603 (2) ball-jointed arm, part no. 401913 how to order accessories magnets and float options field-installed connectors programming tools optional extension rods (for use with captive-sliding magnets)
|
